Ask a consultant a question
+79000978031 Do you want us to call you back?
0
Cart is empty
Cart (0)
Your shopping cart is empty!

PCM NEWS 1.2.5


 ​

 I remind you that from February 21, a new price list begins to operate, and a new version of the bootloader is released - 1.2.5. Changes:

 ​

 1) Added a new module 82 "Bosch SH725xx TCU Bootloader", designed to work in service mode (on the table)

 with Bosch transmission control units with microcontrollers of the SH725xx family used in ZF 8HP, VAG DQ380/381/500,

 MEDG17.9.8, MEG17.9.13, MEG17.9.21, TC60/80. Supports reading, writing, checking and correction of COP in FLASH memory and reading

 and write EEPROM.

 ​

 Attention: Tactrix OpenPort 2.0 adapter is NOT supported at the moment!​

 Tested to work with Scanmatik 2/PRO, Dialink, Chipsoft, Mongoose, CarDAQ.

 ​

 Bosch SH725xx TCU (FLASH) [RD/WR/CK]

 Bosch SH725xx TCU (EEPROM) [RD/WR]

 ​

 2) Added a new module 83 "VAG Bosch DQ380/DQ381/DQ500/ZF 8HP", designed to work through the diagnostic connector

 a car with DSG and automatic transmission units, used in cars of the VAG concern. Reading supported (virtual),

 recording, verification and correction of checksums.

 ​

 DQ380/381/500 (0DE/0DL/0GC) [VR/WR/CK]

 AL450/AL551/AL951 (0CM/0BK/0BL) [VR/RD/WR/CK]

 AL552/AL952 (0D5/0D6) [VR/WR/CK]

 ​

 3) A new module 84 "VAG Delphi DCM6.2" has been added, designed to work through the diagnostic connector of a car with

 Delphi DCM6.2 engine control units used in VAG vehicles. Supports virtual reading

 recording, verification and correction of checksums.

 ​

 1.4L, 1.6L, 2.0L TDI (DCM6.2) [VR/WR/CK]

 ​

 4) A new module 85 "Ford Gearbox" has been added, designed to work through the diagnostic connector of a car with blocks

 6HP26, 5R/6R/6F/8F/10R transmission controls of various modifications used in Ford vehicles. Supported

 reading, writing, checking and correcting checksums.

 ​

 6HP26 TCM [RD/WR/CK]

 5R110 TCM ​ [RD/WR/CK]

 6R80/6R140TCM [BC3A] [RD/WR/CK]

 6F55/8F40/10R80/10R140 TCM [HC3A/HL3A/JL3A/JX6A/LC4A] [RD/WR/CK]

 8F40/10R80/10R140 TCM [K1GA/K2GA/LC3A/LK4A] [RD/WR/CK]

 ​

 5) In module 7 "Ford Transit/Tourneo/Ranger, Land Rover Defender" for ECU SID208, SID209 [CK4A], SID211, read and

 unlocking is now done through the vehicle's diagnostic connector.

 ​

 Attention: in previous versions for the SID211 ECU, the engine size was incorrectly indicated, now this has been corrected.

 ​

 2.2L, 2.4L Diesel 100/125/140/155PS (SID208) [RD/WR/CK/UNLOCK]

 2.2L, 3.2L Diesel (SID209) [CK4A] [RD/WR/CK/UNLOCK]

 2.0L Diesel (SID211) [RD/WR/CK/UNLOCK]

 ​

 6) In module 8 "Mazda generation 1 (2004-2008/10)" protocols have been added to work with Melco transmission control units and

 Aisin used in Mazda vehicles. Reading, writing, verification and correction of checksums is supported.

 ​

 Mazda: Melco TCM (Mazda5/6 512KB) [RD/WR/CK]

 Mazda: Aisin TCM (Mazda MX5 512KB) [RD/WR/CK]

 ​

 7) In modules 9, 10, 11, 72 (Mazda cars), the identification of the ECU type has been added during identification.

 ​

 8) Module 42 "Denso SH705X Bootloader" added support for Denso ECUs using the SH7055 microcontroller and

 installed on Jaguar cars from 2001 to 2008. Supports reading and writing ECU memory via diagnostic

 car connector.

 ​

 Denso: Jaguar X 2001-2008, S/XJ/XK 2003-2006 SH7055 FLASH (512KB) [RD/WR]

 Denso: Jaguar X 2001-2008, S/XJ/XK 2003-2006 SH7055 EEPROM (86) [RD/WR]

 ​

 9) In module 43 "EDC17СP42/MED17" added support for ECUs MED17.8.32, MEDC17.9, EDC17CP55 installed in cars

 JLR groups. Supports reading, writing through the diagnostic connector of the car, as well as checking and correcting

 checksums.

 ​

 Jaguar XE/XJ/F/Range Rover (X152/X351/X760/X761/L405/L494) 5.0L V8 SC (MED17.8.32) [RD/WR/CK]

 Evoque/Discovery Sport 2.0L Diesel (MEDC17.9) [RD/WR/CK]

 Jaguar/Range Rover 3.0L V6, 4.4L V8 Diesel (EDC17CP55) [RD/WR/CK]

 ​

 10) Module 53 "Infineon Tricore BSL" adds support for TC1736 microcontrollers used in some Bosch ECUs.

 ​

 TC1736 MICRO (1024KB) [RD/WR/CK]

 TC1736 EEPROM (32KB) [RD/WR]

 ​

 11) In module 56 "Ford SID807EVO/EDC17C10/EDC17C70" for ECU SID807EVO, reading and unlocking is now done via

 car diagnostic socket:

 ​

 Ford Focus 3: 1.6L DV6C (SID807EVO)[RD/WR/CK/UNLOCK]

 Ford Mondeo 4: 1.6L DV6C (SID807EVO)[RD/WR/CK/UNLOCK]

 ​

 12) Added support for Getrag DC0/DC4 Gen2 (DKG250Gen2) transmission control units in module 58 "VAG DSG/CVT".

 Supports reading and writing ECU memory in service mode.

 ​

 EDC DC0/DC4 Gen2 (DKG250 Gen2) Boot (TC1784/MICRO) [RD/WR]

 EDC DC0/DC4 Gen2 (DKG250 Gen2) Boot (TC1784/EEPROM) [RD/WR]

 ​

 13) In module 68 "JLR Denso" added support for Denso ECUs installed from 2006 to 2010 in

 Volvo XC90 for the European market with 3.2l engine, as well as test support for 4.4l engines.

 It supports reading, writing through the diagnostic connector of the car, as well as checking and correcting checksums.

 ​

 Attention: not all cars are supported!

 ​

 Volvo XC90 29bit 2006-2010 3.2L (Denso) [Test] [RD/WR/CK]

 Volvo XC90 29bit 2006-2010 4.4L (Denso) [Test] [RD/WR/CK]

 ​

 14) Module 74 "Toyota/Lexus generation 3" added support for the ECU used in the 2021 Highlander HV.

 It supports reading, writing through the diagnostic connector of the car, as well as checking and correcting checksums.

 ​

 15) Module 76 "Kia/Hyundai Gearbox" added support for ECU transmission control module MEG17.9.21. Supported

 recording through the diagnostic connector of the car, as well as checking and correcting checksums. ECU reading can

 implemented using module 82.

 ​

 Kia/Hyundai: MEG17.9.21 Gearbox (SH72549/TCU) [WR/CK]

 ​

 16) Added support for automatic transmission ZF 6HP26 with Continental control units in module 81 "JLR Gearbox". Reading is supported

 recording and automatic recognition of its type during these operations, as well as verification and correction of checksums.

 ​

 ZF 6HP26/6HP28 TCM (MPC5xx/TC1766) ​ [RD/WR/CK]

 

 ​